Assembling the OTA

After printing both the top and bottom rings, the mid rings, and the mid plates I started putting together the optical tube assembly (OTA). First I found that the OpenBeam 2.1 was a little too wide for the printed parts. I had orignally tested these parts with an OpenBeam precut kit made up of version 1.0. So, if you are using the files on Thingiverse be sure to make test prints and adjust the size accordingly. Instead of reprinting all of these parts I made the holes larger with an X-Acto knife, files and sandpaper.  

Fig. 1 All of the OTA parts before sanding and general finishing.

Fig. 2 All of the OTA parts before final assembly. 

In figure 2 all of the OTA parts are organized on a table just before assembling them together.  To the bottom left there are all of the mirror cell parts; consisting of the round central hub and three triangular plates for the mirror to sit on.  The spider which holds the secondary mirror is just above that.  To the right in orange are the two main rings that will hold together the main structure of the OTA.  In the top ring is the encoder plate and mid-ring parts that also attach the OTA to the mount.  And to the far right is the rotor which hold half of the magnets in the axial flux motor and will also attach to the other side of the mount.

Below in figures 3 and 4 are up close looks at the top and bottom rings.  The bottom ring holds the mirror cell and the mirror and will have three adjustment knobs for colimation of the optics.  The top ring holds the spider which holds the secondary mirror. The secondary mirror will redirect the light from the primary mirror by 90 degrees to the side of the OTA and into the focuser and eyepiece for viewing the image.

Fig. 3 The bottom ring (orange) and the mirror cell (black) shown upside down after putting together all of the main parts.  The mirror cell here still needs the 3 triangular plates, springs and adjustment screws to hold the mirror. 

Fig. 4 The top ring and spider after assembly.  The secondary mirror will be held in place below the central hub.  

Below in figure 5 the OTA has been joined together by 6 pieces of OpenBeam aluminum extrusion.  The OpenBeam in this picture is 1 meter long and has not yet been cut to its final length.  The 9.75" mirror is intended to be f/3 but has not been finished, thus I will wait to cut the OpenBeam until the focal length of the mirror is set.  Also the focuser board was not placed on the OTA due to fit/finish issues and will be fixed at a later date.  The placement of the mid-plates/axis of rotation is not final because this placement will be chosen once the center of mass of the OTA is finalized.

Fig. 5 The optical tube assembly (OTA), with the rotor plate facing the camera and the encoder plate facing away.  The rotor plate will have 12 magnets placed inside for the altitude motor. 

Over all I am pleased with the look and feel of the OTA.  I will continue to develop the mount and hopefully have some of the parts put together soon.  It's looking like it is possible to develop a high quality 3D printed telescope.  Maybe I'll shoot to have most of this done in time for RTMC in late May of this year. 

Also, I am trying to put together a game plan for developing the hi-resolution absolute encoders for the mount.  In coming posts I will try and go into some more details about how the encoder will work and how I plan to test/develop the hardware and software for the telescope.  

3D Printed Telescope Concept

This is my 3D printed telescope design that I will be working on over the next year or so. The concept came about after seeing a 3D printed axial flux generator (https://www.thingiverse.com/thing:885044 ) and it reminded me of the axial flux motors used by PlaneWave Instruments on the CDK700 telescope and mount observatory system. I wanted to push my Dremel Idea Builder 3D printer as far as it could go and see if I could come up with a telescope and mount with a direct drive motor with goto capabilities. Around mid September I started designing this system around a 9.75” salvaged parabolic mirror. The mirror will be reground to a much shorter focal ratio of f/3 to make the optical tube assembly (OTA) much shorter. This design could also be adapted to different mirror sizes or a different optical design, like a Schmidt Cassegrain. Using TinkerCad I have taken and edited the original stator and rotor, incorporating them into the OTA and fork mount. This design also calls for multiple pieces of OpenBeam (http://www.openbeamusa.com ) extruded aluminum as the main structure of the OTA and mount.

I am going to use this blog to make weekly posts to document this project in as much detail as possible and to hopefully get some feedback on possible improvements or solutions to design issues. All of the design files will be available on httpp://www.thingiverse.com/thing:1112195. Most of the OTA and mount have been designed at this point and I am currently printing out parts and test fitting them one by one. I hope to have a complete bill of materials (BOM) in a future post as the physical design is finalized.

There are a few outstanding issues I'm currently working through and might take some time to find solutions to. First is the absolute encoders needed for pointing and tracking. I am going to try and use inductive sensing via the TI LDC1614 and I will go into more detail about this later (http://www.ti.com/product/ldc1614). Second is the electronics needed to drive the motors and run the goto/tracking of the mount. And last is the large base of the mount that must be printed in pieces due to the small print volume of my Dremel 3D printer. Also, the motor and encoder must be placed next to each other increasing the complexity of the print even more.